【内容】・ＳＭ－５５クロ３ｍｍ×１０００×２０００スライス品で厚み不良

【内容】
・ＳＭ－５５クロ３ｍｍ×１０００×２０００スライス品で厚み不良が発見された。３ｍｍ→４ｍｍ
厚み公差：３．０ｍｍ±０．４
発生数量：部品で約１００ｐｃｓ（１０００×２０００シートより約９０００ｐｃｓ取り）
・発生数量より部分的に厚み不良であったことが考えられます。発生数量より面積は２２２ｃｍ2程です。
【加工方法】
・原反をテーブル上にセットし、回転するバンドナイフ（刃物）により
スライスします。刃物は刃受けで保持されています。
【発生原因】
・部分的な厚み不良であることより、下記原因が推定されます。
・原反下部の刃物入り口部で、刃物・刃受けの抵抗により原反が
瞬間的に持ち上がり浮いた状態になりスライスされた。
・このため厚いものが発生、次の周では薄いものが発生した。
・原反の下部では浮きの現象が稀に発生する場合があります。

Kết quả (Anh) 1:

[Contents]-SM-55 black 3 mm × 1000 × 2000 in slice thickness defect is found. 3 mm-4 mm Tolerance on thickness: 3. 0 mm ± 0. 4 Generation quantity: approx. 100 pcs in part (1000 × 2000 sheets than about 9000pcs取ri)-Might be inadequate thickness than the occurrence quantity partially. Than the occurrence quantity area is 222 cm 2.[Process]By-band stocks and set on the table, to rotate the knife (blade) The slice. Blade keeps in the drill.[Causes]-Partial thickness defect than the inferred cause below.-In the original anti-bottom blade at the entrance of the drill and tool of resistance to the stocks Became momentarily lifted and lifted, sliced.For this is thick and thin what occurs in the next round.At the bottom of the stock float behavior can occur in rare cases.

Kết quả (Anh) 2:

[Contents]
thickness defect is discovered in · SM-55 Black 3mm × 1000 × 2000 slice goods. 3mm → 4mm
thickness tolerance: 3.0mm ± 0.4
generation Quantity: about 100pcs (1000 × 2000 about 9000pcs up the seat) in parts
partially than-generation quantity it is likely that it was the thickness defect. Area than the generation quantity is enough 222cm2.
[Processing method]
the-raw was set on the table, by a band knife for rotation (knife)
and then slice. Cutlery has been held in the blade receiving.
[Cause]
than that, partial and thickness is defective, the following causes is estimated.
Hara at the anti-bottom of the cutlery entrance part, raw is due to the resistance of the receiving knife-blade
I sliced ​​will lift floating state momentarily.
· For this reason thicker occurs, thin thing occurs in the following Zhou.
• In the bottom of the raw might phenomenon of the float is rare occurrence.

Kết quả (Anh) 3:

In 】
content and SM 55 3 mm slice cross 1000 / 2000 found defective. 3 to 4 mm mm mm thickness tolerance: 3.0 0.4 occurred at about 100 pcs Qty: take part in more about 9000 2000 PCs (1000 * sheet including generating quantity and poor in partial thickness were considered. The quantity of generated by process area 222. 2. On the table 】
method, processing method, band knife rotating tool).Slices. The tool is held by the blade. The cause of generating method and 】
partial thickness, it is estimated that cause. In the roll at the entrance of the lower tool blade and blade resistance received by the roll at the moment in a floating state to be lifted. Thick generated at the periphery of the next generation is thin. In the lower part of the original may be generated in a rare phenomenon.